Can I just say I am super excited to be here today to show you what I have been up to? Well, I am! Its me! Sara from
Board and batten has always been a favorite of mine. For something that is actually very simple to do, it makes a huge impact on the space where it is installed. I am a big fan of using other types of wall treatments as well such as
How to Install Floor to Ceiling Board and Batten
Floor to ceiling board and batten can be installed many different ways, with many different materials including MDF (medium density fiberboard) like Cassity used here and wood planks. Both are great ways to install. My favorite way to install board and batten is to use furring strips from your local hardware store. You can usually find these furring strips in an assortment of sizes including 2 by 2 inch square, 1 by 4 inch, and 1 by 3 inch strips.
For this project I used 1 by 3 inch strips. What is great about using these is that they are cheap…like 1 dollar for a 9 foot long board. The cons are that the strips can often be imperfect, including some raw edges, warped pieces, etc. Its worth it to comb through the pile though and find ones that you can use.
The other benefit to using these is that the pieces are already cut! You do not need to buy a 4ft by 8ft sheet of MDF and have it cut down into strips, which can be time consuming.
Start by clearing the space.
The first thing you want to do is find the studs in your wall. You can use a stud finder to do this.
I decided to space by battens 16 inches apart, so always hitting a stud may not be possible, but it is helpful to know where they are at.
The first piece you want to install is a trim piece at the top, along the length of the ceiling.
If you need to install or add to your baseboards this would be the time to do that too. My baseboards are quite thick so I did not need to change them. I kept them in place. Use the stud marks as a guide as to where to nail into the board.
I used my pneumatic brad nailer to nail the pieces into place. This makes really quick work of installing board and batten.
The next step is to install your first vertical piece.
First, you will measure how long it needs to be, and cut your strips accordingly. Now you will place it where you want to install, make sure to use a level to ensure that it is exactly straight vertically then nail the top into place, check for level once again and nail in the bottom. Continue to nail every 6-8 inches all along the board to ensure it is fastened to the wall.
*If you feel like it is not going to be secured to a stud and are worried about it not being secure, you can add a bead of wood glue to the side that will be in contact with the wall. This will give you extra security.*
Now that you have the first piece in place, its time to cut a block. I cut a block 16 inches long. This block will help you install the rest of your pieces quickly.
I apply the block at the top, secure the next piece snug next to it and nail. Then take the block to the bottom of the piece, make sure it is snug and then nail again. Now secure the rest of the piece. Repeat this process until you have all your vertical pieces secured.
Now you are ready to putty and caulk. Putty all the nail holes, and then use a baseboard caulk to fill in the cracks between the wall and the boards. I used spackling compound to fill in the nail holes, since it is easier to work with. This may not be a necessary step, but the whole wall will look much more finished if you do this.
Once everything has dried, its time to sand down any rough spots, or places that were puttied.
Now wipe down the boards, and paint it all. I like to use a roller to paint in between the boards, as well as the tops of the boards. It makes quick work of it all. I then cut in with my angled brush and do all the cracks and corners.
And that’s it!
You can add extra interest to this wall by adding another set of horizontal pieces to create small squares at the top of the wall(which is what I did in my
This is just a sneak peek.
Now, I am off to finish up the rest of the walls the same way! Wish me luck and I hope you’ll stop by to check out what I am up to these days!
More DIY wall treatments